- Bạn vui lòng tham khảo Thỏa Thuận Sử Dụng của Thư Viện Số
Tài liệu Thư viện số
Danh mục TaiLieu.VN
Kĩ thuật biến đổi tương tự – số ADC
Nội dung tài liệu được đề cập đến: Tổng Quan về biến đổi tương tự số(ADC); các phương pháp biến đổi tương tự số (ADC).
16 p hcmute 17/01/2012 274 29
Từ khóa: Điện – điện tử, Kỹ thuật viễn thông, Tự động hóa, Cơ khí chế tạo máy, Kiến trúc xây dựng
Kĩ thuật biến đổi tương tự – số ADC
Nội dung tài liệu được đề cập đến: Tổng Quan về biến đổi tương tự số(ADC); Các phương pháp biến đổi tương tự số (ADC).
16 p hcmute 17/01/2012 334 4
Từ khóa: Điện – điện tử, Kỹ thuật viễn thông, Tự động hóa, Cơ khí chế tạo máy, Kiến trúc xây dựng
Kĩ thuật biến đổi tương tự – số ADC
Nội dung cuốn sách đươc đề cập đến: Tổng quan về biến đổi tương tự - số(ADC); Các phương pháp biến đổi tương tự- số(ADC); Sai số trong biến đổi tương tự -số(ADC).
16 p hcmute 17/01/2012 323 4
Từ khóa: Điện – điện tử, Kỹ thuật viễn thông, Tự động hóa, Cơ khí chế tạo máy, Kiến trúc xây dựng
Kỹ thuật sửa chữa Điện thoại di động 5
Nội dung tài liệu được đề cập đến: Nhiệm vụ của khối điều khiển; Các thành phần trong khối điều khiển; Tín hiệu xử lý trong khối điều khiển – ý nghĩa các linh kiện.
30 p hcmute 17/01/2012 474 37
Từ khóa: Kỹ thuật công nghệ, điện tử, Kỹ thuật sửa chữa, Điện thoại di động, khối điều khiển
Khái quát về hệ thống Phanh - Bánh xe
Nội dung cuốn sách này được đề cập đến: Hệ thống Phanh - Bánh xe.
15 p hcmute 17/01/2012 278 13
Từ khóa: Cơ khí chế tạo máy, Tự động hóa, Điện – điện tử, Kiến trúc xây dựng, kỹ thuật viễn thông
Nội dung cuốn sách được đề cập đến: Cấu tạo hệ thống điều hòa không khí ô tô; Máy nén; Thiết bị ngưng tụ; Thiết bị bay hơi; Bình lọc và hút ẩm; Thiết bị giãn nở
25 p hcmute 17/01/2012 353 7
Từ khóa: Cơ khí chế tạo máy, Tự động hóa, Điện – điện tử, Kiến trúc xây dựng, kỹ thuật viễn thông
Chương 1 Kiến thức cơ sở về SolidWork
Nội dung bài giảng được đề cập đến Kiến thức cơ sở về Solidwork: Bắt đầu với Solidwork; Mở một file đã có; Môi trường phác thảo trong Soidworks; Giới thiệu một số biểu tượng Solidworks; Thanh menu Standard Views; Đặt chế độ lưới trong môi trường vẽ phác thảo; Thanh menu View; Đặt các thuộc tính cho bản vẽ; Một số chức năng của Solidworks.
21 p hcmute 17/01/2012 303 37
Từ khóa: kỹ thuật công nghệ, cơ khí, chế tạo máy, tự động hóa, điện- điện tử
Chương 4: Tạo các đối tượng 3D từ đối tượng 2D
Nội dung cuốn sách này đề cập đến: Tạo đối tượng 3D từ đối tượng 2D; Tạo đối tượng 3D bằng cách kéo theo phương vuông góc với mặt chứa biến dạng,;Tạo đối tượng 3D bằng cách quay đối tượng 2D quanh một trục; Tạo đối tượng 3D bằng cách kéo theo một đường dẫn bất kỳ; Tạo đối tượng 3D từ các biên dạng khác nhau bất kỳ làm trên...
10 p hcmute 17/01/2012 362 9
Từ khóa: kỹ thuật công nghệ, cơ khí, chế tạo máy, tự động hóa, điện- điện tử