- Bạn vui lòng tham khảo Thỏa Thuận Sử Dụng của Thư Viện Số
Tài liệu Thư viện số
Danh mục TaiLieu.VN
Cơ sở thiết kế máy - Phần 2 Truyền động cơ khí - Chương 8
Truyền đai động: Khái niệm chung; Giới thiệu bộ truyền đai Bộ truyền đai (hình 8.1) thường bao gồm: bánh đai dẫn (1), bánh đai bị dẫn (2) và dây đai (3) mắc lên hai bánh đai. Dây đai trong bộ truyền đai là một khâu mềm (khâu dẻo) liên kết hai bánh đai lại với nhau. Các bánh đai được nối với giá bằng khớp quay. Chuyển động quay và tải trọng...
14 p hcmute 17/01/2012 386 14
Từ khóa: giáo trình cơ khí, chế tạo máy, kỹ thuật cơ khí, nguyên lý máy, chi tiết máy
Cơ sở thiết kế máy - Phần 2 Truyền động cơ khí - Chương 7
Truyền động xích: Khái niệm chung; Giới thiệu bộ truyền xích Bộ truyền xích đơn giản (hình 7.1) bao gồm hai đĩa xích (đĩa dẫn 1 và đĩa bị dẫn 2) nối với giá bằng khớp quay và một dây xích (2) (3) (liên kết mềm) mắc trên hai đĩa. (3) Ngoài ra, trong bộ truyền xích còn sử (1) dụng thiết bị căng xích (bộ phận (4) n1 ?2 n2 hình 7.2), thiết bị bôi trơn,...
12 p hcmute 17/01/2012 493 17
Từ khóa: giáo trình cơ khí, chế tạo máy, kỹ thuật cơ khí, nguyên lý máy, chi tiết máy
Cơ sở thiết kế máy - Phần 2 Truyền động cơ khí - Chương 6
Truyền động trục vít: Khái niệm chung; Giới thiệu và phân loại bộ truyền trục vít Bộ truyền trục vít bao gồm trục vít và bánh vít, được dùng để truyền chuyển động và tải trọng giữa hai trục chéo nhau nhờ sự ăn khớp của các ren trên trục vít với các răng trên bánh vít. Thông thường góc chéo nhau giữa hai trục bằng ? = 900, trục vít là trục...
15 p hcmute 17/01/2012 586 22
Từ khóa: giáo trình cơ khí, chế tạo máy, kỹ thuật cơ khí, nguyên lý máy, chi tiết máy
Cơ sở thiết kế máy - Phần 1 Những vấn đề cơ bản trong thiết kế máy và chi tiết máy - Chương 1
Đại cương về thiết kế máy và chi tiết máy:Mỗi máy đ−ợc cấu tạo bởi nhiều bộ phận máy. Mỗi bộ phận máy lại gồm nhiều chi tiết máy. Chi tiết máy lμ phần tử cấu tạo đầu tiên hoμn chỉnh của máy. Ví dụ : Máy tiện gồm nhiều bộ phận máy nh− bμn máy, ụ đứng, ụ động, hộp tốc độ, bμn dao, cơ cấu truyền dẫn từ động cơ đến...
12 p hcmute 17/01/2012 756 44
Từ khóa: giáo trình cơ khí, chế tạo máy, kỹ thuật cơ khí, nguyên lý máy, chi tiết máy
Cơ sở thiết kế máy - Phần 3 Các chi tiết máy đỡ nối - Chương 11
Ổ trục được dùng để đỡ trục, giữ cho trục có vị trí xác định trong không gian, tiếp nhận tải trọng và truyền đến bệ máy. Tùy theo dạng ma sát trong ổ phân thành : ổ trượt (ma sát trong ổ là ma sát trượt) và ổ lăn (ma sát trong ổ là ma sát lăn).
20 p hcmute 17/01/2012 405 7
Từ khóa: giáo trình cơ khí, chế tạo máy, kỹ thuật cơ khí, nguyên lý máy, chi tiết máy
Cơ sở thiết kế máy - Phần 3 Các chi tiết máy đỡ nối - Chương 10
TRỤC 10.1. Khái niệm chung 1. Giới thiệu và phân loại trục Trục dùng để đỡ các chi tiết máy quay (bánh răng, đĩa xích..), để truyền momen xoắn hoặc để thực hiện cả hai nhiệm vụ trên.
9 p hcmute 17/01/2012 543 7
Từ khóa: giáo trình cơ khí, chế tạo máy, kỹ thuật cơ khí, nguyên lý máy, chi tiết máy
Cơ sở thiết kế máy - Phần 2 Truyền động cơ khí - Chương 9
TRUYỀN ĐỘNG VÍT - ĐAI ỐC 9.1. Khái niệm chung 1. Giới thiệu bộ truyền vít - đai ốc Bộ truyền vít đai ốc dùng để biến đổi chuyển động quay thành chuyển động tịnh tiến nhờ sự tiếp xúc và đẩy nhau của ren vít và ren đai ốc. Bao gồm hai bộ phận chính: vít (1) có ren ngoài, đai ốc (2) có ren trong (hình 9.1). ạy dao
8 p hcmute 17/01/2012 450 16
Từ khóa: giáo trình cơ khí, chế tạo máy, kỹ thuật cơ khí, nguyên lý máy, chi tiết máy
Các phương pháp gia công biến dạng - Chương 3c (end)
Dập thể tích 3.5.1. Khái niệm chung a/ Định nghĩa và đặc điểm Dập thể tích là ph-ơng pháp gia công áp lực trong đó kim loại biến dạng trong một không gian hạn chế bởi bề mặt lòng khuôn. Quá trình biến dạng của phôi trong lòng khuôn phân thành 3 giai đoạn: giai đoạn đầu chiều cao của phôi giảm, kim loại biến dạng và chảy ra xung quanh, theo ph-ơng...
28 p hcmute 17/01/2012 462 6
Từ khóa: phương pháp gia công, gia công biến dạng, giáo trình cơ khí, gia công vật liệu, kỹ thuật cơ khí
Các phương pháp gia công biến dạng - Chương 3b
Rèn tự do 3.4.1. Thực chất, đặc điểm và dụng cụ rèn tự do Rèn tự do là một ph-ơng pháp gia công áp lực mà kim loại biến dạng không bị khống chế bởi một mặt nào khác ngoài bề mặt tiếp xúc giữa phôi kim loại với dụng cụ gia công (búa và đe). D-ới tác động của lực P do búa (1) gây ra và phản lực N từ đe (3), khối kim loại (2) biến dạng, sự...
13 p hcmute 17/01/2012 419 9
Từ khóa: phương pháp gia công, gia công biến dạng, giáo trình cơ khí, gia công vật liệu, kỹ thuật cơ khí
Các phương pháp gia công biến dạng - Chương 3a
Các ph-ơng pháp gia công biến dạng 3.1. Cán kim loại 3.1.1.Thực chất của quá trình cán Quá trình cán là cho kim loại biến dạng giữa hai trục cán quay ng-ợc chiều nhau có khe hở nhỏ hơn chiều cao của phôi, kết quả làm cho chiều cao phôi giảm, chiều dài và chiều rộng tăng. Hình dạng của khe hở giữa hai trục cán quyết định hình dáng của sản phẩm. Quá...
12 p hcmute 17/01/2012 397 9
Từ khóa: phương pháp gia công, gia công biến dạng, giáo trình cơ khí, gia công vật liệu, kỹ thuật cơ khí
Qua kiểm tra phân loại để cho phép sử dụng lại các chi tiết còn dùng lại được một cách có hiệu quả tránh lãng phí, loại bỏ những chi tiết bị hư hỏng và xác định những chi tiết có thể sửa chữa, phục hồi để dùng lại. - Việc kiểm tra phân loại tốt sẽ cho phép nâng cao chất lượng và hạ giá thành sửa chữa.
17 p hcmute 17/01/2012 627 10
Từ khóa: sữa chũa ôtô, kỹ thuật sữa chũa ôtô, lý thuyết sữa chũa ôtô, tài liệu sữa chũa ôtô, giáo trình sữa chũa ôtô
QUI TRÌNH CÔNG NGHỆ SỬA CHỮA Ô TÔ
Cốt sửa chữa là bậc tăng (giảm) kích thước của chi tiết lỗ (trục) được qui định giữa nhà chế tạo phụ tùng và người sửa chữa sau mỗi lần sửa chữa. Khi sửa chữa theo cốt, cho phép tiêu chuẩn hoá trong công tác sửa chữa và chế tạo phụ tùng thay thế.
16 p hcmute 17/01/2012 807 25
Từ khóa: sữa chũa ôtô, kỹ thuật sữa chũa ôtô, lý thuyết sữa chũa ôtô, tài liệu sữa chũa ôtô, giáo trình sữa chũa ôtô